I have trouble fixing the terrible seams I’m getting. I’ve followed Elli’s print tuning guide and calibrated extruder, tuned PA (it’s now 0.035) and extrusion multiplier.

I’ve tried adjusting both retraction length and speed, but it doesn’t seem to have much impact. I’m not using “wipe on retract” or “retract on layer change”, I only retract if travel distance is longer than 3mm. Retract is 0.3mm @35mm/s.

I’ve tried reducing PA smooth time too, but this also doesn’t seem to have a noticable impact.

I’ve tried reducing seam gap from the default 10% in Orca all the way down to 0%, but the bad seams persist.

I’ve tried with “wipe on loops” both disabled and enabled with no difference.

I’ve tried with both arachne and classic wall generator, no difference.

I’ve tried different wall orders, inner/outer, inner/outer/inner and outer/inner, all with the same bad seams.

Filament in the picture is matte PLA, it is without doubt dry and generally prints well aside from the seams. It’s stored vacuum sealed with silica, and I use a filament dryer to dry if I suspect wet filament.

I’m running out of ideas for where to tweak to get a decent result.

    • DreadPotato@sopuli.xyzOP
      link
      fedilink
      English
      arrow-up
      2
      ·
      8 months ago

      Yes, I recently switched the hotend from a proprietary one to a regular volcano hotend and did PID tuning.

      • Betch@lemmy.world
        link
        fedilink
        English
        arrow-up
        2
        ·
        edit-2
        8 months ago

        Did you notice this kind of thing happening before you switched your hot end? I’m assuming you’ve tested printing at a higher temp already but I have to ask anyway. 200C is kinda low for some PLAs.

        • DreadPotato@sopuli.xyzOP
          link
          fedilink
          English
          arrow-up
          2
          ·
          8 months ago

          Yeah I’ve tried 190-220C, which is the range specified by the manufacturer of the filament.

          I don’t remember seeing this issue before the change, but I’m still new to the hobby and may just have overlooked or accepted it earlier.

            • DreadPotato@sopuli.xyzOP
              link
              fedilink
              English
              arrow-up
              2
              ·
              8 months ago

              This is just the basic cylinder that’s part of orca slicer that I’m using to troubleshoot the issue because it’s quick to print and the issue is clearly visible.

                • DreadPotato@sopuli.xyzOP
                  link
                  fedilink
                  English
                  arrow-up
                  2
                  ·
                  8 months ago

                  I did also switch to orca around the same time I changed the hotend…I’ll give my old slicer a go as well, maybe it’s a slicer issue.

                  • Betch@lemmy.world
                    link
                    fedilink
                    English
                    arrow-up
                    2
                    ·
                    8 months ago

                    Yeah that’s definitely a possibility. I’m just finishing up my start g-code, gonna see what happens if I try to print that cylinder. Hopefully my printer doesn’t blow up or something 🤞

                  • Betch@lemmy.world
                    link
                    fedilink
                    English
                    arrow-up
                    2
                    ·
                    edit-2
                    8 months ago

                    Could you tell me where in OrcaSlicer you found this cylinder? I can’t seem to find it in the calibration tests.

                    Edit: Nvm found it hahah

                  • Betch@lemmy.world
                    link
                    fedilink
                    English
                    arrow-up
                    2
                    ·
                    8 months ago

                    Well, I just printed a cylinder and my seams are just fine with “default settings”.

                    I say “default” because originally I saw some weird stuff in the preview but it turned out to just be because for some reason spiral vase mode was on by default.